Troubleshooting

Programmes do not start after the loading door is closed.

• Start / Pause /Cancel button might not be pressed. -> Press the Start / Pause /Cancel button.
• It may be difficult to close the loading door in case of excessive loading. -> Reduce the amount of laundry and make sure that the loading door is closed properly.

Programme cannot be started or selected.

• The product has switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). -> Re-set the product back to factory settings by pressing the On/Off button for 3 seconds. (See Cancellation of programme)

If your washing machine does not change programmes, gets stuck or does not continue working; See Changing the Selections After Programme has Started.

Water inside the product.

• Some water has remained in the product due to the quality control processes in the production. This is not a failure; water is not harmful to the product.

The product does not take water in.

• Tap is turned off. -> Turn on the taps.
• Water inlet hose is bent. -> Flatten the hose.
• Water inlet filter is clogged. -> Clean the filter.
• Loading door is not closed. -> Close the door.
• What to do if your machine does receive water see Cleaning the Water Intake Filters.

The product does not drain water.

• Water drain hose is clogged or twisted. -> Clean or flatten the hose.
• Pump filter is clogged. -> Clean the pump filter.

For steps related to checking the water draining hose and cleaning the pump filter see Draining Remaining Water and Cleaning the Pump Filter.

Product vibrates or makes noise.

• Product is standing unbalanced. -> Stable the product by adjusting the feet.
• A hard substance has entered into the pump filter. -> Clean the pump filter.
• Transportation safety bolts are not removed. -> Remove the transportation safety bolts.
• Laundry quantity in the product is too little. -> Add more laundry to the product.
• Excessive laundry is loaded in the product. -> Take out some of the laundry from the product or distribute the load by hand to balance it homogeneously in the product.
• Product is leaning on a rigid item. -> Make sure that the product is not leaning on anything.
• If your machine works loud, see Appropriate Installation Location.

There is water leaking from the bottom of the product.

• Water drain hose is clogged or twisted. -> Clean or flatten the hose.
• Pump filter is clogged. -> Clean the pump filter.

Product stopped shortly after the programme started.

• Machine has stopped temporarily due to low voltage. -> Product will resume running when the voltage restores to the normal level.

Product directly drains the water it takes in.

• Draining hose is not at adequate height. -> Connect the water draining hose as described in the user manual.

No water can be seen in the product during washing.

• Water is inside the invisible part of the product. -> This is not a failure.

Loading door cannot be opened.

• Loading door lock is activated because of the water level in the product. -> Drain the water by running the Pump or Spin programme.
• Product is heating up the water or it is at the spinning cycle. -> Wait until the programme completes.
• Loading door may be stuck because of the pressure it is subjected to. -> Grab the handle and push and pull the loading door to release and open it.
• If there is no power, loading door of the product will not open. -> To open the loading door, open the pump filter cap and pull down the emergency handle positioned at the rear side of the said cap. See “Loading Door Lock”.
• The door of your machine is not opening due to security reasons. -> If the door is locked at the end of the programme when the Wash & Wear option is selected, the machine keeps the door closed until the machine cools down for your safety.

-> If you could not open the door of your washing machine see Loading Door Lock.

Washing takes longer than specified in the user manual.(*)

• Water pressure is low. -> Product waits until taking in adequate amount of water to prevent poor washing quality due to the decreased amount of water. Therefore, the washing time extends.
• Voltage is low. -> Washing time is prolonged to avoid poor washing results when the supply voltage is low.
• Input temperature of water is low. -> Required time to heat up the water extends in cold seasons. Also, washing time can be lengthened to avoid poor washing results.
• Number of rinses and/or amount of rinsing water have increased. -> Product increases the amount of rinsing water when good rinsing is needed and adds an extra rinsing step if necessary.
• Excessive foam has occurred and automatic foam absorption system has been activated due to too much detergent usage. -> Use recommended amount of detergent.

Programme time does not countdown. (On models with display) (*)

• Timer may stop during water intake. -> Timer indicator will not countdown until the product takes in adequate amount of water. The product will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown after this.
• Timer may stop during heating step. -> Timer indicator will not countdown until the product reaches the selected temperature.
• Timer may stop during spinning step. -> Automatic unbalanced load detection system is activated due to the unbalanced distribution of the laundry in the product.

Programme time does not countdown. (*)

• There is unbalanced load in the product. -> Automatic unbalanced load detection system is activated due to the unbalanced distribution of the laundry in the product.

Product does not switch to spinning step. (*)

• There is unbalanced load in the product. -> Automatic unbalanced load detection system is activated due to the unbalanced distribution of the laundry in the product.
• The product will not spin if water is not drained completely. -> Check the filter and the draining hose.
• Excessive foam has occurred and automatic foam absorption system has been activated due to too much detergent usage. -> Use recommended amount of detergent.

Washing performance is poor: Laundry turns gray. (**)

• Insufficient amount of detergent has been used over a long period of time. -> Use the recommended amount of detergent appropriate for water hardness and the laundry.
• Washing has been made at low temperatures for a long time. -> Select the proper temperature for the laundry to be washed.
• Insufficient amount of detergent is used with hard water. -> Using insufficient amount of detergent with hard water causes the soil to stick on the cloth and this turns the cloth into gray in time. It is difficult to eliminate graying once it happens. Use the recommended amount of detergent appropriate for water hardness and the laundry.
• Excessive amount of detergent is used. -> Use the recommended amount of detergent appropriate for water hardness and the laundry.

Washing performance is poor: Stains persist or the laundry is not whitened. (**)

• Insufficient amount of detergent is used. -> Use the recommended amount of detergent appropriate for water hardness and the laundry.
• Excessive laundry is loaded in. -> Do not load the product in excess. Load with amounts recommended in the "Programme and consumption table".
• Wrong programme and temperature were selected. -> Select the proper programme and temperature for the laundry to be washed.
• For more detailed information on washing performance and right programme selection for your washing machine, see Programmes.
• Wrong type of detergent is used. -> Use original detergent appropriate for the product.
• Excessive amount of detergent is used. -> Put the detergent in the correct compartment. Do not mix the bleaching agent and the detergent with each other.

Washing performance is poor: Oily stains appeared on the laundry. (**)

• Regular drum cleaning is not applied. -> Clean the drum regularly. For this procedure, see Cleaning the Loading Door and the Drum.

Washing performance is poor: Clothes smell unpleasantly. (**)

• Odours and bacteria layers are formed on the drum as a result of continuous washing at lower temperatures and/or in short programmes. -> Leave the detergent drawer as well as the loading door of the product ajar after each washing. Thus, a humid environment favourable for bacteria cannot occur in the machine.

Colour of the clothes faded. (**)

• Excessive laundry was loaded in. -> Do not load the product in excess.
• Detergent in use is damp. -> Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures.
• A higher temperature was selected. -> Select the proper programme and temperature according to the type and soiling degree of the laundry.

Washing machine does not rinse well.

• The amount, brand and storage conditions of the detergent used are inappropriate. -> Use a detergent appropriate for the washing machine and your laundry. Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures.
• Detergent was put in the wrong compartment. -> If detergent is put in the prewash compartment although prewash cycle is not selected, the product can take this detergent during rinsing or softener step. Put the detergent in the correct compartment.
• Pump filter is clogged. -> Check the filter.
• Draining hose is folded. -> Check the drain hose.

Laundry became stiff after washing. (**)

• Insufficient amount of detergent is used. -> Using insufficient amount of detergent for the water hardness can cause the laundry to become stiff in time. Use appropriate amount of detergent according to the water hardness.
• Detergent was put in the wrong compartment. -> If detergent is put in the prewash compartment although prewash cycle is not selected, the product can take this detergent during rinsing or softener step. Put the detergent in the correct compartment.
• Detergent was mixed with the softener. -> Do not mix the softener with detergent. Wash and clean the drawer with hot water.

Clothes have shrunk, hardened or spoiled.

• A program not suitable with the laundry type might have been used. -> Select a programme suitable for the laundry by checking the care labels on them and do not use Wash & Wear function selection in laundry not suitable for drying.

Laundry does not smell like the softener. (**)

• Detergent was put in the wrong compartment. -> If detergent is put in the prewash compartment although prewash cycle is not selected, the product can take this detergent during rinsing or softener step. Wash and clean the drawer with hot water. Put the detergent in the correct compartment.
• Detergent was mixed with the softener. -> Do not mix the softener with detergent. Wash and clean the drawer with hot water.

Detergent residue in the detergent drawer. (**)

• Detergent was put in wet drawer. -> Dry the detergent drawer before putting in detergent.
• Detergent has gotten damp. -> Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures.
• Water pressure is low. -> Check the water pressure.
• The detergent in the main wash compartment got wet while taking in the prewash water. Holes of the detergent compartment are blocked. -> Check the holes and clean if they are clogged.
• There is a problem with the detergent drawer valves. -> Call the Authorised Service Agent.
• Detergent was mixed with the softener. -> Do not mix the softener with detergent. Wash and clean the drawer with hot water.
• Regular drum cleaning is not applied. -> Clean the drum regularly. For this procedure, please see Cleaning the Loading Door and the Drum.

Too much foam forms inside the product. (**)

• Improper detergents for the washing machine is used. -> Use detergents appropriate for the washing machine.
• Excessive amount of detergent is used. -> Use only sufficient amount of detergent.
• Detergent was stored under improper conditions. -> Store detergent in a closed and dry location. Do not store in excessively hot places.
• Some meshed laundry such as tulle may foam too much because of their texture. -> Use smaller amounts of detergent for this type of item.
• Detergent was put in the wrong compartment. -> Put the detergent in the correct compartment.
• Softener is being taken early by the product. -> There may be problem in the valves or in the detergent drawer. Call the Authorised Service Agent.

Foam is overflowing from the detergent drawer.

• Too much detergent is used. -> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer. -> Put detergent into the product suitable for the programmes and maximum loads indicated in the “Programme and consumption table”. When you use additional chemicals (stain removers, bleaches and etc.), reduce the amount of detergent.

For steps on how to use laundry detergents and auxiliary products; click here. Using Detergent and Softener.

Laundry comes out damp at the end of the programme when Wash & Wear function is selected.

• Excessive laundry is loaded in. -> Load maximum 1 kg when Wash & Wear option is selected.
• Function is not active. -> Check if Wash & Wear function is selected after the selected washing programme.

Laundry remains wet at the end of the programme. (*)

• Excessive foam has occurred and automatic foam absorption system has been activated due to too much detergent usage. -> Use recommended amount of detergent.

(*) The product does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the product and to its surrounding environment. Laundry should be rearranged and re-spun.

(**) Regular drum cleaning is not applied. Clean the drum regularly. See “Cleaning the loading door and the drum”

WARNING

WARNING:

Check the HomeWhiz section for the relevant troubleshooting information regarding HomeWhiz.